固件编译

开始编译

固件编译简明指南

注意事项

• 网络: 确保上位机(树莓派等)已联网
• 登录方式: 必须使用 SSH 通过网络登录，禁用串口
• 输入法: 保持键盘为英文半角模式

---

SSH登录与用户切换

使用 MobaXterm、PuTTY 等工具 SSH 登录上位机。

切换用户：

• 普通系统(树莓派官方系统等)
  禁止使用 root,需切换到普通用户：

  su <用户名>

• FLY上位机(FlyOS-FAST系统)
  仅支持 root 用户登录(密码： mellow)

---

固件编译操作指南

在 Klipper 固件配置界面中仅支持键盘操作,无法使用鼠标。

按键	功能
↑ / ↓	上下移动光标，选择菜单项
Enter / 空格	确认选择、勾选选项或进入子菜单
ESC	返回上一级菜单
Q	退出配置界面
Y	退出时，如有提示则按 Y 保存配置

开始固件编译

下面介绍如何编译固件：

1. 连接到 SSH，输入下面的命令并按 Enter：

   cd ~/klipper && rm -rf ~/klipper/.config && rm -rf ~/klipper/out && make menuconfig

   其中，rm -rf ~/klipper/.config && rm -rf ~/klipper/out 用于清除之前的编译配置与固件； make menuconfig 用于打开 Klipper 固件配置界面。

2. 按照下方顺序逐项设置，每完成一项再继续下一项。

   1启用 Enable extra low-level configuration options

   (Top)

   Klipper Firmware Configuration

   [*] Enable extra low-level configuration options

   Micro-controller Architecture (Raspberry Pi RP2040/RP235x) --->

   Processor model (rp2040) --->

   Bootloader offset (No bootloader) --->

   Flash chip (W25Q080 with CLKDIV 2) --->

   Communication Interface (USBSERIAL) --->

   USB ids --->

   [*] Optimize stepper code for 'step on both edges'

   (gpio8) GPIO pins to set at micro-controller startup

   GPIO state at micro-controller startup (Not set) --->

   [Space/Enter] Toggle/enter[?] Help[/] Search

   [Q] Quit (prompts for save)[Esc] Leave menu

   2Micro-controller Architecture 选择 Raspberry Pi RP2040/RP235x

   (Top)

   Klipper Firmware Configuration

   [*] Enable extra low-level configuration options

   Micro-controller Architecture (Raspberry Pi RP2040/RP235x) --->

   Processor model (rp2040) --->

   Bootloader offset (No bootloader) --->

   Flash chip (W25Q080 with CLKDIV 2) --->

   Communication Interface (USBSERIAL) --->

   USB ids --->

   [*] Optimize stepper code for 'step on both edges'

   (gpio8) GPIO pins to set at micro-controller startup

   GPIO state at micro-controller startup (Not set) --->

   [Space/Enter] Toggle/enter[?] Help[/] Search

   [Q] Quit (prompts for save)[Esc] Leave menu

   3Processor model 选择 rp2040

   (Top)

   Klipper Firmware Configuration

   [*] Enable extra low-level configuration options

   Micro-controller Architecture (Raspberry Pi RP2040/RP235x) --->

   Processor model (rp2040) --->

   Bootloader offset (No bootloader) --->

   Flash chip (W25Q080 with CLKDIV 2) --->

   Communication Interface (USBSERIAL) --->

   USB ids --->

   [*] Optimize stepper code for 'step on both edges'

   (gpio8) GPIO pins to set at micro-controller startup

   GPIO state at micro-controller startup (Not set) --->

   [Space/Enter] Toggle/enter[?] Help[/] Search

   [Q] Quit (prompts for save)[Esc] Leave menu

   4Bootloader offset 选择 No bootloader

   (Top)

   Klipper Firmware Configuration

   [*] Enable extra low-level configuration options

   Micro-controller Architecture (Raspberry Pi RP2040/RP235x) --->

   Processor model (rp2040) --->

   Bootloader offset (No bootloader) --->

   Flash chip (W25Q080 with CLKDIV 2) --->

   Communication Interface (USBSERIAL) --->

   USB ids --->

   [*] Optimize stepper code for 'step on both edges'

   (gpio8) GPIO pins to set at micro-controller startup

   GPIO state at micro-controller startup (Not set) --->

   [Space/Enter] Toggle/enter[?] Help[/] Search

   [Q] Quit (prompts for save)[Esc] Leave menu

   5Flash chip 选择 W25Q080 with CLKDIV 2

   (Top)

   Klipper Firmware Configuration

   [*] Enable extra low-level configuration options

   Micro-controller Architecture (Raspberry Pi RP2040/RP235x) --->

   Processor model (rp2040) --->

   Bootloader offset (No bootloader) --->

   Flash chip (W25Q080 with CLKDIV 2) --->

   Communication Interface (USBSERIAL) --->

   USB ids --->

   [*] Optimize stepper code for 'step on both edges'

   (gpio8) GPIO pins to set at micro-controller startup

   GPIO state at micro-controller startup (Not set) --->

   [Space/Enter] Toggle/enter[?] Help[/] Search

   [Q] Quit (prompts for save)[Esc] Leave menu

   6Communication Interface 选择 USBSERIAL

   (Top)

   Klipper Firmware Configuration

   [*] Enable extra low-level configuration options

   Micro-controller Architecture (Raspberry Pi RP2040/RP235x) --->

   Processor model (rp2040) --->

   Bootloader offset (No bootloader) --->

   Flash chip (W25Q080 with CLKDIV 2) --->

   Communication Interface (USBSERIAL) --->

   USB ids --->

   [*] Optimize stepper code for 'step on both edges'

   (gpio8) GPIO pins to set at micro-controller startup

   GPIO state at micro-controller startup (Not set) --->

   [Space/Enter] Toggle/enter[?] Help[/] Search

   [Q] Quit (prompts for save)[Esc] Leave menu

   7USB ids 保持默认，无需进入

   (Top)

   Klipper Firmware Configuration

   [*] Enable extra low-level configuration options

   Micro-controller Architecture (Raspberry Pi RP2040/RP235x) --->

   Processor model (rp2040) --->

   Bootloader offset (No bootloader) --->

   Flash chip (W25Q080 with CLKDIV 2) --->

   Communication Interface (USBSERIAL) --->

   USB ids --->

   [*] Optimize stepper code for 'step on both edges'

   (gpio8) GPIO pins to set at micro-controller startup

   GPIO state at micro-controller startup (Not set) --->

   [Space/Enter] Toggle/enter[?] Help[/] Search

   [Q] Quit (prompts for save)[Esc] Leave menu

   8启用 Optimize stepper code for 'step on both edges'

   (Top)

   Klipper Firmware Configuration

   [*] Enable extra low-level configuration options

   Micro-controller Architecture (Raspberry Pi RP2040/RP235x) --->

   Processor model (rp2040) --->

   Bootloader offset (No bootloader) --->

   Flash chip (W25Q080 with CLKDIV 2) --->

   Communication Interface (USBSERIAL) --->

   USB ids --->

   [*] Optimize stepper code for 'step on both edges'

   (gpio8) GPIO pins to set at micro-controller startup

   GPIO state at micro-controller startup (Not set) --->

   [Space/Enter] Toggle/enter[?] Help[/] Search

   [Q] Quit (prompts for save)[Esc] Leave menu

   9GPIO pins to set at micro-controller startup 设置为 gpio8

   (Top)

   Klipper Firmware Configuration

   [*] Enable extra low-level configuration options

   Micro-controller Architecture (Raspberry Pi RP2040/RP235x) --->

   Processor model (rp2040) --->

   Bootloader offset (No bootloader) --->

   Flash chip (W25Q080 with CLKDIV 2) --->

   Communication Interface (USBSERIAL) --->

   USB ids --->

   [*] Optimize stepper code for 'step on both edges'

   (gpio8) GPIO pins to set at micro-controller startup

   GPIO state at micro-controller startup (Not set) --->

   [Space/Enter] Toggle/enter[?] Help[/] Search

   [Q] Quit (prompts for save)[Esc] Leave menu

   10GPIO state at micro-controller startup 选择 Not set

   此项是 FLYOS-Klipper 功能。通常保持 Not set；如需设置全部 GPIO 的启动状态，请先阅读 GPIO 启动状态使用说明。

   (Top)

   Klipper Firmware Configuration

   [*] Enable extra low-level configuration options

   Micro-controller Architecture (Raspberry Pi RP2040/RP235x) --->

   Processor model (rp2040) --->

   Bootloader offset (No bootloader) --->

   Flash chip (W25Q080 with CLKDIV 2) --->

   Communication Interface (USBSERIAL) --->

   USB ids --->

   [*] Optimize stepper code for 'step on both edges'

   (gpio8) GPIO pins to set at micro-controller startup

   GPIO state at micro-controller startup (Not set) --->

   [Space/Enter] Toggle/enter[?] Help[/] Search

   [Q] Quit (prompts for save)[Esc] Leave menu

   11按 Q 键退出配置界面

   (Top)

   Klipper Firmware Configuration

   [*] Enable extra low-level configuration options

   Micro-controller Architecture (Raspberry Pi RP2040/RP235x) --->

   Processor model (rp2040) --->

   Bootloader offset (No bootloader) --->

   Flash chip (W25Q080 with CLKDIV 2) --->

   Communication Interface (USBSERIAL) --->

   USB ids --->

   [*] Optimize stepper code for 'step on both edges'

   (gpio8) GPIO pins to set at micro-controller startup

   GPIO state at micro-controller startup (Not set) --->

   [Space/Enter] Toggle/enter[?] Help[/] Search

   [Q] Quit (prompts for save)[Esc] Leave menu

   12出现 Save configuration 时按 Y 保存配置

   Quit

   Save configuration?

   (Y)es(N)o(C)ancel

3. 完成上方最后两个步骤，按 Q 退出配置界面，再按 Y 保存配置。

4. 返回命令行后输入下面的命令并按 Enter 开始编译：

   make -j4

   root@flyos-11e5f8 ~/klipper # make -j4

   Compiling out/src/rp2040/bootrom.o

   Compiling out/src/rp2040/usbserial.o

   Compiling out/src/generic/usb_cdc.o

   Compiling out/src/rp2040/chipid.o

   Compiling out/src/rp2040/hard_pwm.o

   Compiling out/src/rp2040/spi.o

   Compiling out/src/rp2040/i2c.o

   Preprocessing out/src/rp2040/rpxxxx_link.ld

   Building out/compile_time_request.o

   Version: XXXX

   Linking out/klipper.elf

   Creating uf2 file out/klipper.uf2

   终端末尾出现 Linking out/klipper.elf 和 Creating uf2 file out/klipper.uf2，即表示编译成功。 实际编译时，部分 Compiling 行和 Version 会随 Klipper 与系统版本变化。

进入烧录模式

提示

圈起来为BOOT按键

• 进入烧录模式需要主板完全断电,按住BOOT按键然后将带有数据传输的数据线一头接主板一头接上位机
  Loading...

烧录固件

• 请注意当前工具板是处于固件烧录模式，只能烧后缀名为uf2的固件

• 通过下方命令将固件烧录到工具板

  cd && cd ~/klipper/
  make flash FLASH_DEVICE=2e8a:0003

  提示

  如果是上位机写好系统后第一次烧录，可能会出现和下图红圈中一样的提示——出现部分红色提示，此为正常现象，并非报错。

  Loading...

确认固件是否启动

• 如果固件正常启动LED会亮起来

Loading...