FLY-D5 Bootloader (Katapult) Recovery
Firmware Description
- Fly-D5 motherboard Only via USB Type-C port for BL flashing
- The Katapult firmware is pre-installed by default from the factory
Entering Flash Mode
The left is the RST button, and the right is the BOOT button.
- There are two ways to enter flash mode.
- Method 1: With the motherboard completely powered off, press and hold the BOOT button, then connect one end of a data-capable TYPE-C cable to the motherboard and the other end to your device.
- Method 2: After connecting one end of a data-capable TYPE-C cable to the motherboard and the other end to your device, press and hold the BOOT button, then press the RST button, then release the RST button, and finally release the BOOT button.
Loading...
Flashing Firmware
- WIN flashing
- LINUX/FLYOS flashing
- D5 Katapult firmware
- You can obtain the firmware from the following link:
.txt 或其他扩展名。- The firmware is located at
FLY-Firmware/MainBoard/D
- STM32CubeProgrammer
- DFU-AUTO
Before connecting or reconnecting the USB cable, completely turn off the printer and disconnect all other power supplies. Do not let the tool board be powered simultaneously through the printer power supply and the USB interface.
The USB interfaces on some computers may cause unstable flashing due to driver or signal compatibility issues. If the connection fails, try using a different USB interface on the computer or use a reliable-quality USB dock; when the error shown below appears, also check the USB connection and driver first.
- Download and install
SetupSTM32CubeProgrammerand the STM32 DFU driver from the auxiliary software download page. - Save the firmware downloaded on this page to a location on your computer that is easy to find.
Windows may hide file extensions. In File Explorer, check "File name extensions" to confirm that the firmware is still .bin or .hex, and do not change the file extension.
- Confirm that the device has entered DFU flashing mode according to the product tutorial, then connect it to the computer using a USB cable that supports data transfer.
- Open STM32CubeProgrammer, select USB mode, refresh the device list, and connect.
- If no error pop-up appears, the connection is successful.
- Click the download icon on the left, and check the flashing options as shown in the figure below.
- Click
Browseand select the firmware to be flashed.
- When flashing
.binfirmware, setStart addressto0x08000000; when using.hexfirmware, keep the address included in the file.
- Click
Start automatic modeto begin flashing.
- When the success prompt appears, the firmware flashing is complete.
Before connecting or reconnecting the USB cable, completely power off the printer and disconnect other power sources. Do not let the toolboard be powered simultaneously by both the printer power supply and the USB interface.
- Download and run FLY DFU-AUTO.
- If the "Driver Status" shows unavailable, click "Install Driver" to complete the WinUSB driver installation.
- Click "Browse" to select the
.binfirmware file to be flashed.
Windows may hide file extensions. In File Explorer, check "File name extensions" to confirm the firmware remains as .bin. Do not modify the file extension.
- Click "Start Flashing", monitor progress through the run log, and wait for the flashing process to complete.
Detailed Tutorial: FLY DFU-AUTO Download and Usage
- Linux
- FLYOS
- Install flashing tool.sudo apt updatesudo apt install dfu-util -y
- Confirm the device has entered DFU flashing mode.lsusb
If you can see 0483:df11, it means DFU flashing mode has been entered successfully.
Loading... - Pull/update firmware repository.git clone https://cnb.cool/3dmellow/FLY-Firmware ~/FLY-Firmwarecd ~/FLY-Firmware && git pull --ff-only
- Flash firmware.
FLY_D5.binsudo dfu-util -a 0 -d 0483:df11 --dfuse-address 0x08000000 -D ~/FLY-Firmware/MainBoard/D/FLY_D5.bin - If File downloaded successfully appears, flashing is successful.Loading...
- FLY host computer usually has dfu-util built-in, no need to install flashing tool again.
- Confirm the device has entered DFU flashing mode.lsusb
If you can see 0483:df11, it means DFU flashing mode has been entered successfully.
Loading... - Pull/update firmware repository.git clone https://cnb.cool/3dmellow/FLY-Firmware /data/FLY-Firmwareln -s /data/FLY-Firmware /root/FLY-Firmwarecd /data/FLY-Firmware && git pull --ff-only
- Flash firmware.
FLY_D5.binsudo dfu-util -a 0 -d 0483:df11 --dfuse-address 0x08000000 -D /data/FLY-Firmware/MainBoard/D/FLY_D5.bin - If File downloaded successfully appears, flashing is successful.Loading...